More > JRiver Media Center 24 for Linux
Docker for MC24?
Scobie:
Thanks Jatzoo, I will give that a try when I get a moment.
Appreciate your ongoing support.
NH:
Dear Jatzoo, other knowledgeable folks on the topic
Many thanks for your detailed instructions on installing JRiver in docker. I have managed to install.
However I am not able to get inside JRiver to complete the settings. I have tried realvnc viewer, tightvnc and putty.
I had pointed it to port 32769 on the IP address of the QNAP NAS which was the port assigned during set up. I get a message "connection closed unexpectedly" or "connection gracefully closed" (tightVNC!).
Is it some settings in QNAP that is preventing this access?
Best
NH
Best
Will be grateful for your advice
NH:
--- Quote from: NH on February 24, 2021, 06:04:52 am ---Dear Jatzoo, other knowledgeable folks on the topic
Many thanks for your detailed instructions on installing JRiver in docker. I have managed to install.
However I am not able to get inside JRiver to complete the settings. I have tried realvnc viewer, tightvnc and putty.
I had pointed it to port 32769 on the IP address of the QNAP NAS which was the port assigned during set up. I get a message "connection closed unexpectedly" or "connection gracefully closed" (tightVNC!).
Is it some settings in QNAP that is preventing this access?
Best
NH
Best
Will be grateful for your advice
--- End quote ---
Further, wanted to check what is the reason that when you access the port you are led to the MC panel, not the standard MC interfacet that you see on Windows. If one were to land there, there is no need for a VNC server to do the settings. For example, I have seen the way SongKong has created their docker image, which when I followed the step by step instructions and you go to port number 4567, you see exactly the same screens as you would see on a Windows desktop. It was done in 5 mins! There was no need for any VNC etc to do the settings and didnt need any other knowledge. Any of you can check it out here. http://www.jthink.net/songkong/install_docker_qnap.jsp
If this is possible at all (and you are the expert!) this would make it very simple. And all QNAP users would be very grateful.
The option of keeping a PC running all the time with MC on is not working out for me and since the NAS runs all the time, this way I would be able to access it as a player also. Else I am only able to use it for editing, music management etc but not really for playng. I end up using minimserver and bubbleupnp to stream it to my ethernet DAC.
Best
NH
Jatzoo:
@NH, what is Your configuration for point 5 from this instruction:
https://yabb.jriver.com/interact/index.php/topic,115841.msg821370.html#msg821370
PS. You must use VNC to log-in to MC and configure it on the server side (Qnap). If You don't want to do it in this way, there are some other docker images where GUI MC can be accessed via web browser.
NH:
--- Quote from: Jatzoo on February 26, 2021, 03:33:19 am ---@NH, what is Your configuration for point 5 from this instruction:
https://yabb.jriver.com/interact/index.php/topic,115841.msg821370.html#msg821370
--- End quote ---
Thanks Jatzoo. The configuration I have is what you have shown under NAT. It doesnt allow me to use Host networking.
What I see on the overview screen as URL is http://10.X.X.X:32787/ -> 52199. Still cant access through VNC.
Tried Bridge networking also - same result.
On the access via web gui, if that's easier, will be grateful if you tell me which ones I can use. Will check them out.
Best
NH
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version