More > JRiver Media Center 24 for Windows

ASIO Live problem with RME device

<< < (2/2)

mattkhan:

--- Quote from: BradC on January 17, 2019, 04:36:57 pm ---I was able to get it to work by setting jriver output to wasapi instead of asio.

--- End quote ---
that sounds like a multiclient issue then, i.e. the RME driver not supporting a multiclient mode. I do remember having some issues this when I used to have an RME FF800.

pschelbert:
Hi

I had this issue and solved it some time ago. Its somewhere on this forum, but I better post the "how to" again.

The point is somehow the RME-Driver does not route inputs directly to JRiver, you need first the input to route to output, then that output configue "Loopback" and the it shows up in "open live". Right offset may be a bit crucial, try and try systematically.

I just hera over opne live now, JRiver MC24.0.72PC and RME UFX, Driver of RME: 1.1.66.0

Here how to:

RME UFX
1) go to HARDWARE PLAYBACK /RME Totalmix FX
Select to which output the signal shall go by clicking on the output.
Example: ADAT15/16

2) go to HARDWARE INPUTS / RME Totalmix FX
Signal on analog input, I have there Vinyl/Turnetable:
Example: Analog3/4
Set Volume Slider to volume you want, example: 0dB
Mute: off (button not blue)

Now the signal of Analog3/4 goes to output ADAT15/16

3) go to HARDWARE PLAYBACK /RME Totalmix FX
Click on an output
Example: ADAT15/16
Volume Slider: can be anything
Mute: off or on does not play a role
Loopback: ON,  this is they key!!! turn Looback ON

Now the Signal on inputs 3/4 is routed back to to inputs ADAT15/16. You dont see it in the meters!

Now: JRiver, "OPEN Live ASIO", Offset x
In the example. ADAT15/16 are channel 29 and 30. Therefore offset=28 results in 29>1, 30>2 mapping.

An you got your turntable signal, Analog3/4 into JRiver.

Peter

cyberkul:

--- Quote from: pschelbert on January 19, 2019, 05:29:17 am ---Hi

I had this issue and solved it some time ago. Its somewhere on this forum, but I better post the "how to" again.

The point is somehow the RME-Driver does not route inputs directly to JRiver, you need first the input to route to output, then that output configue "Loopback" and the it shows up in "open live". Right offset may be a bit crucial, try and try systematically.

I just hera over opne live now, JRiver MC24.0.72PC and RME UFX, Driver of RME: 1.1.66.0

Here how to:

RME UFX
1) go to HARDWARE PLAYBACK /RME Totalmix FX
Select to which output the signal shall go by clicking on the output.
Example: ADAT15/16

2) go to HARDWARE INPUTS / RME Totalmix FX
Signal on analog input, I have there Vinyl/Turnetable:
Example: Analog3/4
Set Volume Slider to volume you want, example: 0dB
Mute: off (button not blue)

Now the signal of Analog3/4 goes to output ADAT15/16

3) go to HARDWARE PLAYBACK /RME Totalmix FX
Click on an output
Example: ADAT15/16
Volume Slider: can be anything
Mute: off or on does not play a role
Loopback: ON,  this is they key!!! turn Looback ON

Now the Signal on inputs 3/4 is routed back to to inputs ADAT15/16. You dont see it in the meters!

Now: JRiver, "OPEN Live ASIO", Offset x
In the example. ADAT15/16 are channel 29 and 30. Therefore offset=28 results in 29>1, 30>2 mapping.

An you got your turntable signal, Analog3/4 into JRiver.

Peter

--- End quote ---

Hi! Old thread, but I have the same problem. I`m trying to get a signal from my turntable through the JRiver convolution engine. I use Audiolense to generate a convolution filter for room-correction, crossovers and RIAA, and use this filter in the JR convolution engine.

 I have connected the turntable DL103R signal to the RME UFX mic-input 11 and 12. Then I enabled loopback on the ADAT1/2 output. Tried many different ch. offsets in "Open live", but no signal. I see no signal on the outputs in RME TotalMix, except on the ADAT1/2 output. If I check the box "Listen to this device" in the Win10 sound recording devices I get a signal on all the used outputs in TotalMix, and also get a signal in JRiver, OpenLive. Offset doesn`t matter. I guess Win10 is resampling the Turntable input signal when the "Listen to this device" is checked? Can it be that the ch. offset is still the problem? Where can I find the offset numbers for the UFX? I thought this was the numbers seen in the TotalMix, Matrix view? For ADAT1/2 it should be around 12 I think. If I hoover the mouse pointer over the "Gear" symbol", the speed shows 0x realtime. If there is a signal this number is usually 4-5.

Navigation

[0] Message Index

[*] Previous page