Devices > Video Cards, Monitors, Televisions, and Projectors
Dealing with windows 7 dynamically handling video outputs?
Bill Kearney:
Anyone figured out how to properly configure win7 to avoid it rejiggering the video outputs all the time?
I've got an Nvidia GT430 (I think) in the machine and every time I change the video output the screen resolution gets confused. I've got two outputs on the card, one VGA and the other HDMI. The VGA runs to a KVM on my desk (so I can reconfigure things as needed without going to the TV). The HDMI is connected to a matrix switch (a monoprice 4x4 unit). Off the matrix it can be connected to any one of four outputs. Right now it's connected to a Pioneer VSX-82TSX (avr) and a Pioneer Pro-1140HD Plasma. At some point it'll also be connected to two other outputs (after we remodel the whole house).
When I change the output from the AVR to the TV the video driver things get screwy. First it loses the HDMI output, reconfiguring the PC to use only the VGA output. Then as it makes the switch to one of the outputs it reconfigures the desktop to have two side-by-side desktops. I can then bring up the Display control panel and configure the desktops as duplicates of each other. Sometimes it'll either stick with the 1360x768 resolution I've chosen for them, or it'll go with whatever it's decided are the native resolutions. But it's inconsistent on this.
The same sort of thing happens to the audio outputs.
So, any tips on preventing this nonsense? I just want to force it to duplicate the desktops and leave 'em at a given resolution.
jmone:
Some GPU's handle the EDID change "better" than others but I've found my trusty DVI Detective+ keeps the PC happy as I switch from a TV and/or PJ as it keeps broadcasting the same EDID even if there is no active screen/avr at the other end (note: the "modern" version is the HDMI Detective I believe).
Bill Kearney:
The downside to the HDMI Detective is it's limited in what resolutions and audio formats it supports. If you're fine with the limited subset then it might be OK. But for $100 *per device* that's a bit expensive. From what I gather I'd have to put one on each source output, before it goes into the matrix switch. This would let the source devices all think they're still talking to the same output device. This, apparently, is important when it comes to avoiding audio output limitations. As in, you get stuck using only stereo output because that's the lowest common denominator across all your TVs. So your home theater projection TV and receiver wouldn't be able to use 7.1 surround (or the like) because there's a low-end TV in the office that only accepts stereo.
I think there's a little more planning required here. I'll have to look into this audio limiting issue more. I don't feed multiple TVs yet but will after we remodel. So I'll have the option to order whatever TVs are 'most compatible' with the whole system. Or, as some people are doing, use an AVR in places where the TV display alone wouldn't do a good enough job. Perhaps only using it as a way to 'downgrade' from the distributed HDMI signal to whatever the lower-end TV supported.
jmone:
My DVI Detective Plus has presets (which I dont use) and the ability to record a live EDID feed that it will then always transmit. I've done this when the PJ was being used (via the AVR) so I now get the PC "seeing" EDID data for all the supported audio options from the AVR in addition to the 3d info from the PJ even if it is not connected. The result is the PC never changes it's audio or video settings regardless of what device I actually have on and connected.
Sandy B Ridge:
I used a HDMI Detective for a while (until I figured I could do without it with a firmware update for my amp). I used it because I wanted to have the flexibility to completely turn off the TV whilst listening to audio. Previously my HTPC (and PS3, so not a windows issue!) would stop sending audio to the amp as soon as the TV turned off since the EDID would change forcing a re-handshake and audio stopping. Using the HDMI Detective sorted it. The amp manufacturer produced a firmware update which fixed the EDID in place if it lost the 'sink' which was great for my needs.
Anyway, the HDMI detective is programmable. You can make it learn what EDID table you wish it to send out. It also has a few in-built EDID tables (with 7.1 support for audio IIRC). I think you may only need one device on the back of the PC rather than several, so I would try this first.
You could probably find the manual for the device online somewhere to see how it works. If it doesn't work for you, you could always put it 'On the Bay'. There was a healthy market for these a while back, especially in Europe where they were closer to £100 (=$160) than $100. So you may not lose much by giving it a go.
SBR
Navigation
[0] Message Index
[#] Next page
Go to full version