More > Old Versions
MC18 Won't Play High Resolution FLACs
Jeff_N:
Hello,
I'm running MC 18.0.212 on a little Asus netbook with Windows 7. A USB cable goes from the netbook to my Cambridge DACMagic.
Most of my music files are FLACs stored on the netbook. My MC Options settings are:
Output mode: WASAPI
Output mode settings: the DAC is default (I also disabled the onboard audio card to make sure it wasn't interfering)
"Open device for exclusive access" is checked.
"Disable event style" is unchecked.
Bit depth: Automatic
Buffering: 100 milliseconds
In the Advanced Properties section of Windows the only audio device that now appears is the DAC. I've checked both "Allow applications to take exclusive control of this device" and "Give exclusive mode applications priority." I've disabled all enhancements.
My 44.1kHz/16bit FLAC files play fine and sound great. But when I try to play 96kHz/24bit FLAC files I get no sound and an error window that reads:
"Playback could not be started using the format: 96kHz 24bit 2ch. This format would work: 48kHz 24bit 2ch."
I've searched here and on the Computer Audiophile site. Others seem to have had similar problems but nothing quite like this. Another thread here suggested changing the bit depth in the Output settings, and I tried a few, but other than causing MC to buffer for a few seconds and then stop trying it had no effect.
Incidentally, if I switch output mode to ASIO I still get nothing. Direct Sound does play the files, but of course I don't want to use that, I'd like bit-perfect output.
I know the DACMagic is capable of handling 96kHz/24bit files. Does anyone have any idea what I'm doing wrong?
Thank you for looking.
kensn:
Dose your Cambridge DAC show it supports 96khz/24bit in windows?
Ken
Jeff_N:
Yes it does, it even has indicator lights to register incoming sample rates of 44.1, etc up to 96.
Arindelle:
Hi Ken
I had a DacMagic.
I remember having to set the bitdepth manually to 24bits in previous versions (although I thought that by 18.0.212 this issue was adressed), so try it on your setup. I don't remember if you have the choice in version 18 of 24 bit or 24 bit with a 32bit float or not ... try both see what happens. Your other settings are spot on, they will work so don't change those.
Post back if this doesn't work.
Also in DSP studio, when using the DacMagic I had checked "output format". For all the sample rates I set this to "no change" up to 96kHz; above 96, I forced MC to downsample to 96k. This will allow you to play higher rez through this DAC without getting that screen shot about not starting playback. You will also notice that if you play 48k or 88.2k, files the blue indicators will (should^^) light up with the correct incoming sample rates.
BTW : do you have an SPDIF output -- optical or coax. Sort of doubt it on a netbook, but if so give it a try. Thought both of these were really better much than the USB connection for this DAC. The DacMagic+ has an asynchronous USB, but not the older DacMagic
Jeff_N:
Thanks for your help Arindelle.
I tried all the different bitdepth options and here are the results.
Automatic: plays 44.1/16 but not 96/24.
16 bit: plays 44.1/16 but not 96/24.
24 bit: won't play either resolution.
24 bit in 32 bit package: won't play either resolution.
32 bit: won't play either resolution.
32 bit floating point: won't play either resolution.
I'm using the sample rates you suggested in DSP.
You're right, there's no SPDIF port on the netbook.
Unless you have a better idea I guess I'll try downloading a trial version of MC19 to see if that works. If it doesn't, I'll try other software like Foobar. And if THAT doesn't work, I suppose I'll have to start looking for a new DAC. Thanks again.
Navigation
[0] Message Index
[#] Next page
Go to full version