More > JRiver Media Center 20 for Linux
JRiver Media Center 20.0.129 for Debian (Wheezy) ARM
PrinterPrinter:
--- Quote from: bob on June 12, 2015, 11:00:51 am ---You didn't say if you tried the fixed format output instead of Auto.
The other difference between MC and other programs is that it doesn't use the linux resampler. You could set DSP studio to resample everything to a specific rate to see if that changes anything.
Also, set the track transition to gapless and turn off the eliminate silence switch.
Other that that, I'm not sure where else we can go with this. MC uses a very simple interface to the sound device so it's not likely that changes in MC will affect this, especially since it doesn't seem to be present in other devices.
--- End quote ---
Thanks Mate,
I'll try these suggestions.
To be honest I suspect this is more of a Raspberry Pi issue rather than MC - you've all been very helpful and kind - thank you!
Hilton:
I've upgraded the Pi to the new branch Linux raspberrypi 4.0.5-v7+ #797.
All working great.
PrinterPrinter:
--- Quote from: Hilton on June 23, 2015, 07:18:58 pm ---I've upgraded the Pi to the new branch Linux raspberrypi 4.0.5-v7+ #797.
All working great.
--- End quote ---
Thanks mate,
Sounds promising.
Can I ask you for the command(s) to use?
Hilton:
There's a lot of new drivers and some drivers haven't been brought across yet that were in the old branch on version 3 kernel.
Unless you know what you're doing, experiencing problems or are prepared to rebuild from scratch I'd stay on that current 3 branch for now. It should be fine but its still very new and there maybe undetected regressions(problems).
To upgrade to the latest stable use sudo apt-get update and then sudo apt-get upgrade
This will upgrade all installed software to the latest stable release and is less likely to have problems than changing to the latest branch.
If you really want to temp fate you can run sudo apt-get update and then sudo apt-get install rpi-update
This will install a firmware/kernel update tool which can be used to get onto the latest branch. It can break things, so do so in the full knowledge you may have to rebuild your Pi from scratch.
Finally... if your really really sure.. the command to upgrade to the latest branch is sudo rpi-update
You have been warned! :)
Hilton:
When successful you should get this output.
pi@raspberrypi ~ $ sudo rpi-update
*** Raspberry Pi firmware updater by Hexxeh, enhanced by AndrewS and Dom
*** Performing self-update
% Total % Received % Xferd Average Speed Time Time Time Current
Dload Upload Total Spent Left Speed
100 10185 100 10185 0 0 29302 0 --:--:-- --:--:-- --:--:-- 32333
*** Relaunching after update
*** Raspberry Pi firmware updater by Hexxeh, enhanced by AndrewS and Dom
#############################################################
WARNING: This update bumps to rpi-4.0.y linux tree
Be aware there could be compatibility issues with some drivers
Discussion here:
https://www.raspberrypi.org/forums/viewtopic.php?f=29&t=113753
##############################################################
Would you like to proceed? (y/N)
*** Downloading specific firmware revision (this will take a few minutes)
% Total % Received % Xferd Average Speed Time Time Time Current
Dload Upload Total Spent Left Speed
100 168 0 168 0 0 111 0 --:--:-- 0:00:01 --:--:-- 139
100 46.7M 100 46.7M 0 0 37123 0 0:22:00 0:22:00 --:--:-- 203k
*** Updating firmware
*** Updating kernel modules
*** depmod 4.0.6+
*** depmod 4.0.6-v7+
*** Updating VideoCore libraries
*** Using HardFP libraries
*** Updating SDK
*** Running ldconfig
*** Storing current firmware revision
*** Deleting downloaded files
*** Syncing changes to disk
*** If no errors appeared, your firmware was successfully updated to a51e2e072f2c349b40887dbdb8029f9a78c01987
*** A reboot is needed to activate the new firmware
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version