INTERACT FORUM
Networks and Remotes => Media Network => Topic started by: MikeO on September 21, 2017, 10:55:26 am
-
Hi the set up is Big PC as MC server, Cambridge Audio CXN as renderer as a Zone in MC
JRemote as control
My problem is that running, I get a consistent skip track 1 then track 3 . It's always Track 2 that skips
Any ideas, the rest of the album plays fine, but skip happens a lot, maybe not every album but probably half !!
Mike
-
Hi the set up is Big PC as MC server, Cambridge Audio CXN as renderer as a Zone in MC
JRemote as control
My problem is that running, I get a consistent skip track 1 then track 3 . It's always Track 2 that skips
Any ideas, the rest of the album plays fine, but skip happens a lot, maybe not every album but probably half !!
Mike
The renderer is probably not supporting SetNextAVTransportURI properly.
Right click on the renderer zone then find DNLA controller option and turn off SetNext support.
-
Hi Bob
The setup has been like this for over 2 years. This has only just started.
There have been no firmware updates to the CXN for over a year
Mike
-
Did you try Bob's suggestion?
-
I tried with MC22 and MC23. They both skip with the Cambridge Audio NP30 we have here for testing.
This was not the case before, the NP30 was one of the few devices that seemed to support SetNext properly.
And that is the issue. Turning off SetNext support fixes the skip.
-
Tracing the dump from the NP30 turned up an issue with the DLNA controller option "Ignore GetPosition failure". This option helps with non-compliant firmware.
The NP30 is improperly sending back a server error for a function required to be supported by the protocol, I assume yours is doing the same.
With the next build of MC the Option will not be on by default (the logic was reversed) so now the default will be to use the relaxed testing.
This will avoid triggering the bug in your firmware and fixes the skip issue without turning off the SetNext (gapless) support.
-
Sounds good, I'll keep an ear open, I installed 62 this morning
Mike
-
Sounds good, I'll keep an ear open, I installed 62 this morning
Mike
Did that make a difference?
-
Sorry got a bit busy
I have tried a couple of albums, and on 2nd mc skipped track 2 the other ran ok
It's not consistent
I'll try and put some time into it
Mike
-
Still happening
Just updated to build 70 , there is a reference to something like this as being fixed . Is that it ??
Mike
-
Still happening
Just updated to build 70 , there is a reference to something like this as being fixed . Is that it ??
Mike
Several things were fixed and enhanced.
Do you have "Ignore GetPosition Failure" on or off?
-
I now have
Ignore Transport Events - Unticked
Disable Set Next Support - Ticked
Ignore Get Position Failure - Ticked
I assume this won't impact gapless playback
Lets see what happens
Thanks for the input
Mike
-
And is it working with that setup?
-
It plays ... ;D but I prefer Abbey Road without the Gaps & Stutters ....
I took off the 2 ticks and gapless returned , I haven't had chance to check if Track 2 skipping is OK yet
Maybe I put the ticks back one at a time
Any suggestions which is the offender
Mike
-
It plays ... ;D but I prefer Abbey Road without the Gaps & Stutters ....
I took off the 2 ticks and gapless returned , I haven't had chance to check if Track 2 skipping is OK yet
Maybe I put the ticks back one at a time
Any suggestions which is the offender
Mike
I use Abbey Road as my gapless test! I'm sure everyone here is getting sick of it ;)
The option to Ignore GetPosition failure will prevent gapless playback since we need to know the position to determine when to send the next track.
I think you should try it with everything unticked (which does have different behavior from the previous build) and if that doesn't work, with just Ignore Transport Events ticked.
-
I'll try all unticked
I'll see if I can drive my wife mad with Dark Side Of The Moon ;D
Mike
-
I'll try all unticked
I'll see if I can drive my wife mad with Dark Side Of The Moon ;D
Mike
"There is no Dark Side of the Moon really, it's all dark!" 8)