Devices > Video Cards, Monitors, Televisions, and Projectors
MadVR exlusive mode blackblinking and glitches and washed out color no brightnes
tkolsto:
Okey! I have my windows resolution setting always at 60 hz because then interpolation/dejuddar does better when playing( 50 hz) netflix hbo youtube(all through opera browser, not jriver). I then tried to set it at 120 hz. then I got the black blinking away using 3d 11. and 120 fps 5 pull down playing a movie in madvr. I set it back to 60 fps and still the black blinking is gone. Exclusive mode is not ok then, leaving doubt and uease of things not being as it should be.
But I still got glitches. and when trying playing with videoclock and hardware accelerating video decoding. I found out that I unticked hardware accelerating video decoding, then the glitches stopped, but as I wrote only using 3d 11,exlusive mode is not usable, which is an indicator that something is not 100 persent. But I think though that 3d 11 and 120 hz/fps which forces 5 pull down(same frames presented 5 times to cope with oleds instant rapid presentation of frames) is working now as it should, I hope.
another thing which happened along tweaking..is that when I installed the new rtx card...I got pretty high rendering milliseconds..at about 8 milliseconds, compare to 3050s 14/15 milliseconds. but along the way it is now about 3 milliseconds, which would be more as is should be for this high end card. and this is after playing starting and restarting jriver which I do every time I start the movie again.
So I now think I am able to play movies(23fps video) using 120 fps/hz( osd shows 119880hz and this is also chosen in windows resolution when I go in there to check, It stays there at 119880..hz also when I am not playing movie. So it should be able to do 120 hz/fps. I dont know what to think of this though. I see the movement is the best I have seen not using dejudder. paning is bad as you said. I think I have to play some movies to see if I get used to it.
I have to compare it with ...using madvr and dejudder and pixel shaders and using highligth recovery strength which actually reduces artfacts created from dejudder /motion artifacts.
tkolsto:
Something is not as it should be. That is for sure.
I Am back to my old gpu. and I am not able to do the same 5 pull down same setting, even set madvr to lowest quality performance setting which is for low end gpu“s. So that is not how it supposed to be. 3050 aint that bad.
I seams that 3070 ti card is so strong that it solves the difficulties that I have on the pc. that is why there are no glitches.
eve:
--- Quote from: tkolsto on October 14, 2022, 02:16:48 pm ---Something is not as it should be. That is for sure.
I Am back to my old gpu. and I am not able to do the same 5 pull down same setting, even set madvr to lowest quality performance setting which is for low end gpu“s. So that is not how it supposed to be.
--- End quote ---
I don't really understand any of this process.
In your previous post you said you had gotten things working
--- Quote ---So I now think I am able to play movies(23fps video) using 120 fps/hz( osd shows 119880hz and this is also chosen in windows resolution when I go in there to check, It stays there at 119880..hz also when I am not playing movie. So it should be able to do 120 hz/fps. I dont know what to think of this though. I see the movement is the best I have seen not using dejudder. paning is bad as you said. I think I have to play some movies to see if I get used to it.
--- End quote ---
If it works here, why did you go back to the old GPU? Following along with your post, you got a 3070ti, got it working, and then removed it?
Sell your 3050 or use it elsewhere and use the 3070ti for media playback right now. Clearly it's working.
tkolsto:
But why does exclusive mode not work with a brand new gpu? Is not that a bit strange? It was so large that I had to remove some discs to be able to install it. I have to go for another card, like 3060 ti, which is more than enough I would think. I went back to the old gpu because I thought I had solved the issue by using 3d 11 and 5 pullddown and untick accelerate video decoding(which stopped the glitches). but that was not the case at all.
I am going to try it one more time. but not to night. I have to work tomorrow. I cant have this card to big and I cant afford it either at the moment. But glad I tried it. 3060 ti is probably more than enough like You said.
tkolsto:
I am going to try some movies that I did not get to try because they where one the discs I had to remove.
I am going to test more movies. It was the best I have seen without dejudder, but I am not sure this paning and tracking motion is something I can get used to. I am going to try alien covenant to see how the stutter is in the entire opening scene in the bright white rom...and also several scenes where the spaceships paning over the screen. If it is bad I probably have to live with interpolation and keeping my old card. Frankly when things are not working properly I dont want to pay so much money anymore at the mess of a tv pc purchase. I have used 1500 dollar on the TV and 1300 dollar on a desktop and still get bad result and it should actually be perfect everything working perfectly which it does not. overall I am very diassapointed of the TV and Pc. But this is how things are in oled world. I am very pleased that You have helped me and I now know how to use 5 pull down. I will probably buy 3060ti when I get the money. If I am pleased with 3070ti. the next days I am going to use it to see more movies. and decide if this is something I can use.
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version