Devices > Video Cards, Monitors, Televisions, and Projectors

MadVR exlusive mode blackblinking and glitches and washed out color no brightnes

<< < (9/16) > >>

eve:

--- Quote from: tkolsto on October 14, 2022, 04:16:02 pm ---But why does exclusive mode not work with a brand new gpu?  Is not that a bit strange? It was so large that I had to remove some discs to be able to install it. I have to go for another card, like 3060 ti, which is more than enough I would think. I went back to the old gpu because I thought I had solved the issue by using 3d 11 and 5 pullddown and untick accelerate video decoding(which stopped the glitches). but that was not the case at all.
I am going to try it one more time. but not to night. I have to work tomorrow.  I cant have this card to big and I cant afford it either at the moment. But glad I tried it. 3060 ti is probably more than enough like You said.

--- End quote ---

Some of the new cards are HUGE. 3060tis can get pretty small though, I forget which one we have slapped in my desktop but IIRC it's compact.

I can't really tell you why exclusive mode isn't working for you. Too many variables.


Don't buy a 3060ti new if you actually are planning on keeping it, they're getting really affordable used b/c the crash. The retail prices are quite out of pace with what they're worth.

tkolsto:
eve. when You use 5 pull down/120 hz/fps one can choose whatever hdr madvr setting in madvr one like, like pixel shader and dont activate the hdr logo/tvs hdr? I think maybe it is best just to use pixel shader and not tick off ,send hdr data til the Tv? or do you just choose let madvr decide? And maybe You turn off tonemapping when one use Tvs hdr handeling? Or does nothing of this matter and one can choose whatever one want? I think I read somewhere that the ting now was to not activate hdr and just let madvr to everything in processing of videos?

tkolsto:
just reinstalled rtx 3070. I have not done anything yet other than reading forum on jriver. and it looks like the card is running warm under no load. The card got a huge heat sink( new cards got huge sink so that fans should only go on when it get warm) and the fans go on and off all the time. it goes on for a minute and then off for two minutes or three. this is unormal behaviour and somethings make the gpu go warm and that under no load. My other rtx 3050 did the same and when I used msi afterburner to control the gpu fan it was ok. And when I uninstalled the msi afterburner it contiued to stay quiet. Just want to write all that is not normal.

tkolsto:
I finally got to test alien covenant. and it was not good at all. stutter in most movement. only calm static pictures where ok as they always are. I did not noticed this on interstellar but had a strong suspicioun that this was the case. The opening scene in alien covenant in the white room was awful. and the scenes where the spaceship flying over the screen likewise. This is a clear dealbreaker. Interpolation and pixel shader and the use of highligth recovery strength is a better solution. But the problem here is that it is not rock solid, sometimes it is tight and is all good and then othertimes it is like things are not cooperating and create bad motion like geting clear artifacts or small hang ups in images, hard to explain. but when this happens motion is not good.

I do think that is shouldnt be so bad and that it is only like on this on my screen/TV or maybe You have the same and does not care. My initial thought was that all motion more or less was stutterfree and with uniform images in motion, without the shivering effect on movement. It would have been nice to know if You had the same result on your setup in this movie. I doubt you would consider it a good choice. I got the impression that You got a tight motion and only some little tiny stutter one very rapid motion and that only on large "bad" panning of the whole image would get some judder stutter.

If You have the same result more or less, then I can not use this. Then Oled is crap in my eyes and unbelievable that people can watch it. I do think it might be something wrong with my pc or tv and that is why I get black blinks in exlusive mode wich is a huge alarm bell since this should scorn JRiver for any inteference from other misbehaving software.

tkolsto:
and now also the fan is noisy which indicate that gpu struggles after I just ticked on some features in madvr processing setting(did not tinker with the settings just ticked it and used what was already suggested). aritfact removal and image enhancement(this last one got all the fans get noisy) I dont know that much about these features, but should this not be a no match of this gpu? thus another indicator that something is wrong and draw a lot of power that it shouldnt draw? or these setting insanely impacting the gpu and is normal. I am just playing around with this gpu now to see what it is good for. I did not touch these settings on the above rendering of alien covenant.

I also tested this youtube video of greece at 10 min 50 sec and then let it play for some seconds showing the camera come out from a tunnel in the mountain and the rocks is shivering on the right of the tunnel as the camera flyes out ot the tunnel. so this card is not performing better than my 3050. this happens when I play this video in 120 hz and interpolation dejudder at 7 and bfi at low. I does not handle this. I have to set resolution in windows to 60 hz and then it is almost perfect. https://www.youtube.com/watch?v=RSRKFAmfqnI&t=691s

Navigation

[0] Message Index

[#] Next page

[*] Previous page