INTERACT FORUM

Please login or register.

Login with username, password and session length
Advanced search  
Pages: [1]   Go Down

Author Topic: SOLVED: Display settings disappear when switching between monitor and projector  (Read 2384 times)

Trumpetguy

  • Citizen of the Universe
  • *****
  • Posts: 974

I have a dual screen setup, with a vga cable to a monitor and hdmi to a projector. The monitor does not have 1920x1080x24 mode, the projector does. Projector desktop and monitor viewing mode 60Hz for computer use, with film modes 23.796 and 24 to be shown as 1920x1080x32x23 on the pj. Every time the projector is switched off, the film viewing modes are reset to "desktop setting". In practice this means I need to change display settings every time I want to watch a movie.

Is there any way MC can be configured not to forget these settings?
Logged

SamuelMaki

  • World Citizen
  • ***
  • Posts: 115
Re: Display settings disappear when switching between monitor and projector
« Reply #1 on: November 20, 2011, 07:20:49 am »

If you use madVR, then you can use its own refresh changer and configure projector and monitor...
Logged
AMD Phemon II N930 Quad 2.0ghz, AMD Radeon HD 5650, 4GB RAM, Windows 8 RP x64

mbagge

  • Galactic Citizen
  • ****
  • Posts: 255
Re: Display settings disappear when switching between monitor and projector
« Reply #2 on: November 20, 2011, 11:06:45 am »

Does the hdmi connection go directly to the projector or via some kind of avr?
Displays, projectors and alike sends a edid token to explain its capabilities and when your projector is connected through an avr and not turned on, the avr sends its own edid, not the one from the projector. Then the pc reconfigures your setup. Quite annoying.
Logged

Trumpetguy

  • Citizen of the Universe
  • *****
  • Posts: 974
Re: Display settings disappear when switching between monitor and projector
« Reply #3 on: November 20, 2011, 11:38:56 am »

No avr, hdmi directly into pj. And it is MC that looses its video configuration. There is no mismatch between htpc and pj.

I will look into madVR also, to see if that is a way around.
Logged

Trumpetguy

  • Citizen of the Universe
  • *****
  • Posts: 974
Re: Display settings disappear when switching between monitor and projector
« Reply #4 on: November 20, 2011, 01:09:34 pm »

It seems simply to be so that MC detects the possible monitor/pj resolutions and refresh rates. If I send video signal to my monitor, the "impossible" video settings (1080p24) is replaced by "desktop settings". I can understand that trying to play back 1080p24 on my monitor would cause a black screen, but it would really be convenient to force MC to remember the settings. I usually do not watch movies on my 19" monitor (obviously), but I frequently (always) use it between two movies.
Logged

Sandy B Ridge

  • Citizen of the Universe
  • *****
  • Posts: 884
Re: Display settings disappear when switching between monitor and projector
« Reply #5 on: November 20, 2011, 04:17:23 pm »

Try the EDID Override thread on Avsforum.

I had a similar issue, but it was my amp that kept 'forgetting' that it could do 24p. This meant that MC defaulted to 'desktop settings' when it forgot.  Installing an inf file for your projector might make the setting stick. It may not work because you turn the pj off, whereas my problem was the amp was always on, but reporting the wrong EDID.

SBR
Logged

Matt

  • Administrator
  • Citizen of the Universe
  • *****
  • Posts: 42441
  • Shoes gone again!
Re: Display settings disappear when switching between monitor and projector
« Reply #6 on: November 20, 2011, 08:53:10 pm »

I have the same problem at home.

I'd like to switch it so that display settings are zone specific. 

It also shouldn't revert if it fails to load a refresh rate, for the reasons you've listed.

If this doesn't happen in the next two weeks, please bump this thread.

Thanks.
Logged
Matt Ashland, JRiver Media Center

Trumpetguy

  • Citizen of the Universe
  • *****
  • Posts: 974
Re: Display settings disappear when switching between monitor and projector
« Reply #7 on: November 21, 2011, 12:18:57 pm »

Thanks a lot for looking into this. I'll make sure to bump into the thread if nothing happens!
Logged

Matt

  • Administrator
  • Citizen of the Universe
  • *****
  • Posts: 42441
  • Shoes gone again!
Re: Display settings disappear when switching between monitor and projector
« Reply #8 on: November 21, 2011, 05:09:51 pm »

I think this will be all better in build 17.0.40 (or newer), including keeping settings and making the settings zone-specific.

Check back later this week or early next week.

Thanks.
Logged
Matt Ashland, JRiver Media Center

Trumpetguy

  • Citizen of the Universe
  • *****
  • Posts: 974
Re: Display settings disappear when switching between monitor and projector
« Reply #9 on: December 04, 2011, 01:12:36 pm »

17.0.40 (11/21/2011)
14. Changed: Display changing settings in Options > Video are now zone-specific (may require manually reconfiguring applicable video options).

I tested this, and it works exactly as i hoped for, thanks a lot!

It allows me to open Display Settings on my RGB monitor without losing its PJ settings. It also allows playback of 24Hz material on the 60Hz monitor without losing settings. Best of all - when firing up my 1080p24 PJ, it remembers the auto-switching to 1920x1080x24 even if I did all those things in between. Great :-)
Logged
Pages: [1]   Go Up