INTERACT FORUM

Great, 1.1.0 uses the right repos for older versions and a new alpine-based container for checking the latest MC version. This will save about 80MB of disk space and bandwidth on first install.

Switch out of secure mode if the disk is really hashed.  It might just not be able to get a secure rip on some discs.

MC ripped the first six tracks then just spun for a half hour.  So, I don't think it is copy protected.  Meanwhile, MC finished playing the song it was playing and then went silent and wouldn't respond. 

I ripped the CD using iTunes with no problems.  It's a well-used CD, so it's understandable that MC would  have trouble with it, but a more graceful failure mode would be an improvement.  I've seen it do this probably a dozen times or so when ripping a "marginal" CD.

Still looking for help.

A good part of my reason, for going with MC was the support staff at Moon Audio, but a few others, in another forum, were also pushing in this direction.
ALL saying the "forum help" is really good.

 Difficult to tell if I'm just not getting it or there are some bugs to work out. But not getting any responses to my questions and it is a bit frustrating.

1st - I seem to have all my music in the player = great ! I can go to "albums" for example..clik on that icon. At the bottom of the screen, I can see the header;
 title / artist /album / genre   etc as expected.
Yet, I can Not see, or see How  to show anymore...ie; the actual track listings ?!? 
 So if I wanted to say take a track, to add to a CD I wish to rip, nothing allows me to do that, because I can't see it ?!?
The other recommendation, which is supposed to help me view my music on the A&K SR35, which is also the whole point...is to Convert all the music to Flac
which I have been doing. However, very early in the process, maybe 2500 songs, got a warning from the Mac that I'm running out of disk space ?!?
Not knowing enough, I suspect there are some simple solutions,  yet ?

thanx

Let it run.

It's possible the CD is copy protected.  Not common but possible.

Antivirus can also be a problem.

When ripping a CD the software hung at some percentage and would not respond.  Attempting to end the process using task manager resulted in an access denied message.  Restarting the computer would not fix the problem - I got the message that MC was already running.  I needed a hard reboot (unplug the computer) to get MC to run again.

I upgraded to v32, but the problem persists. It is a specific CD that is problematic (actually there are three today that exhibit this behavior.) I've attached the log file.

Windows 10, 64bit, MC v 32 (just downloaded the latest version)

Try Options > Tree & View > Full Screen (Display View... > Monitor

I was aware of that setting but had assumed that the description of Full Screen (Display View, Theatre View, etc) meant everything would move to the designated monitor. Clearly, I read far more into that "etc" than was really intended. It actually just affects Display View, Theatre View, and Cover View -  but not Standard View or Mini View. It therefore does just what I wanted!

Many thanks for that. It makes Theatre View much more practical for me 

Arconis Cyber Protect HO: 1 Computer (1 year License) incl. 500 GB Cloud Space cost me 89.99€ per year. (40€ per year is the Cloud part)

For me it's ok. The point for me to choose Acronis was that I wanted Cloud from the Backup SW Vendor. If I would have a Synology NAS for Backup, I would backup to Synology C2 Coud.

One Workflow - One Management Front End.

Try Options > Tree & View > Full Screen (Display View... > Monitor

Maybe it is there already, but I dont know how. I have problems with normally just getting 1 to 3 repeated frames during a movie and sometings a few framedrops, in both hdr and sdr(hdr not activated) and also some very small fluctiatins in measured vsync. earlier it was steady as rock. videoclock or hardware accelarated decoding is not enabled. Have tried them out but same result. From what I have experienced ..is best rendering without using videoclock and hardware accele...enabled. So cpu is more used instead of mostly gpu.
I have used both 531.79 and latest studiodriver 555.85.

Maybe this windows 11 is doing bad updates..bc I never did anything to my pc that should create this problem.

So is there possible to make a feature to check repeated, dropped or glitches not only during but also after the movie is finnished. So I can check it after the movie is over and the osd is gone?